Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

$1.80 - $7.35
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
$15.95
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
$15.95
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
$11.50 - $48.00
We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels
$28.82 - $34.15
Surly Ultra New Axle Kits are for upgrading the internals of your existing Surly New hubs or replacing the internals on your Surly Ultra New hubs. -Compatible with Surly New hubs (upgrade kit) and Surly Ultra New hubs (replacement kit) - Each kit contains an axle, two 6901 cartridge bearings, two aluminum dust shields, two stainless steel cones, two stainless steel 6x1mm bolts, and two stainless steel bolt washers - Axle is quick release and bolt-on compatible; bolts included, QR is NOT included - Standard Surly New hubs come stock with 7901 bearings; this kit uses 6901 bearings which are non-angular
$10.00
- Replacement steel quick release skewers
$10.00
- Replacement rear skewer - Spacing: 135mm - Material: Steel
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$39.00
The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button-head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - One-piece design - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6 mm hex wrench required for installation
$2.99
The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.
$31.99
V2 Tubeless valves are stronger, lighter, and even easier to use thanks to the machined aircraft grade 7075 aluminum and Muc-Off's new Tire Insert air ?ow system. The new design features six slots that are machined into the base of the valve stem, allows tubeless sealant ?uid and air to ?ow freely, even when running tubeless tire inserts. - 7075 Machined Aluminum valve stem and cap - Tire Insert air flow system keep air moving freely and compatible with most tire foam inserts - 4mm machined Allen Key slot for easy installation and removal - Includes Valve Core Removal Tool (integrated into spare alloy cap) - Supplied with various rubber bases to optimize fit with multiple rim types
$6.70 - $16.99
Grade 10 chromium steel balls
$15.39 - $21.69
Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.
$57.76
The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - Weight: starting at 20g for 64 nipples
$24.00
Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).
$151.00
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
$24.00
Includes rim strip and tubeless tape for 1 wheel.
$70.00
- Wheel bearing kit front/rear - Bearing dimensions: 17 x 30 x 7mm - Material: steel - 2 pieces
$19.00 - $31.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.
$7.00
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.
$390.00
- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed
$129.00 - $216.00
Freehub bodies for Zipp Cognition hubs.
$206.00
Zipp Speed Weaponry Rear Axle Conversion Kit - Not to be used on 188 V6 or earlier rear hubs - Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed
$21.00
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.
$19.00
A simple solution for completing the Zipp aerodynamic package by covering the valve access hole on most disc wheels. Black, self-adhesive oval patches with the Z logo, in a package of five.
$108.00
Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1) Compatible With: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1
$106.00
Wheel Freehub Kit—XD Driver Body Kit—Zipp ZM2 - Compatible With: WH-MOTO-30-B1
$27.00
Rear Wheel Axle for X0 hubs, including the following wheels: Rise 60 (B1), Roam 30, Roam 40, Rail 40, Rise XX, Roam 50, 60 B1 Compatible with part numbers: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1
$49.00
- Hub axle end cap set, rear - Zipp Cognition V2 Disc Brake - Rim brake compatible with XDR & 11-speed
$49.00
- Hub axle end cap set, rear - Zipp Cognition V2 Rim Brake - Quick release
Page 1 of 10 Next page